There have been papers that analyze the relationship between bit design and a bit’s vibrational characteristics. These papers typically are based on the analysis of three-axis near-bit down-hole vibration sensors. In this paper, the authors take a simpler approach. Using a standard microphone literally pointed at the bit, they record the noise of the bit/rock interaction while drilling and analyze the resulting noise for these bit vibrational characteristics. The data were gathered at the Colorado School of Mines in Golden, CO. The noise of a PDC core, roller cone, and diamond core bits were recorded under various weight and rotary speeds using a microphone and a vertically mounted uniaxial geophone (used for confirming the data recorded on the microphones). Using a Fast Fourier Transform, the frequency spectra were extracted from the recorded data and analyzed. The data were normalized for rotational speed. The results of the frequency analysis of the roller cone, the PDC, and the natural diamond bits are presented in this paper. The major differences in the three bit frequency characteristics could be detected and furthermore, for drag bits, the frequency characteristics could be related to the bit’s design. The frequency spectra of the roller cone bit can best be described with a general high amplitude level that is relatively evenly distributed over the whole frequency spectrum. The drag bit data showed a strong relationship between the number and arrangement of cutting elements and frequency peaks on a plot of amplitude versus cycles per revolution. Frequency peaks were observed at multiples of the number of cutting elements. In general this relationship was strongly visible on the PDC bit data but not as strongly visible on the diamond bit data. The conclusion is that bit characteristics can be determined using only the noise of a bit. Potential applications of this research include detecting and diagnosing bit problems (e.g., broken teeth and bit balling) in real time using simple microphone based acoustic data.
Skip Nav Destination
Article navigation
March 2012
Research Papers
An Analysis of Noise Characteristics of Drill Bits
Alfred W. Eustes,
Alfred W. Eustes
Colorado School of Mines
Search for other works by this author on:
Gerhard Thonhauser
Gerhard Thonhauser
Montanuniversität Leoben
Search for other works by this author on:
Christian Gradl
Hess Energy
Alfred W. Eustes
Colorado School of Mines
Gerhard Thonhauser
Montanuniversität Leoben
J. Energy Resour. Technol. Mar 2012, 134(1): 013103 (7 pages)
Published Online: December 23, 2011
Article history
Revised:
August 3, 2001
Received:
July 10, 2009
Online:
December 23, 2011
Published:
December 23, 2011
Citation
Gradl, C., Eustes, A. W., and Thonhauser, G. (December 23, 2011). "An Analysis of Noise Characteristics of Drill Bits." ASME. J. Energy Resour. Technol. March 2012; 134(1): 013103. https://doi.org/10.1115/1.4005324
Download citation file:
Get Email Alerts
Stage-wise kinetic analysis of ammonia addition effects on two-stage ignition in dimethyl ether
J. Energy Resour. Technol
Related Articles
Analysis and Application of a New Hybrid Drill Bit for Use in Hard Rocks
J. Energy Resour. Technol (December,2022)
A Model of Performance and Life of Diamond Drill Bits
J. Pressure Vessel Technol (May,1978)
Design Considerations for Development of a Wire-Based Rock Cutting Mechanism for Space Exploration
J. Mech. Des (November,2010)
Life Models for Small-Diameter Polycrystalline Diamond Compact Bits in Hard Abrasive Media
J. Energy Resour. Technol (December,1986)
Related Proceedings Papers
Related Chapters
Drilling Economics
Oilwell Drilling Engineering
Erosion and Corrosion of WC-Base Matrix Materials and Their Impregnated Diamond Composites for Drill Bits under the Impingement of Drilling Fluids
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
Image Processing Based Analysis of Diamond Exposure on the Crown of Impregnated Diamond Bit
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)