Transient pressure peak values and decay rates associated with water hammer surges in fluid lines are investigated using an analytical method that has been formulated, in a previous publication, to simulate pressure transients in turbulent flow. The method agrees quite well with method of characteristics (MOC) simulations of unsteady friction models and has been verified with experimental data available for Reynolds numbers out to 15,800. The method is based on the formulation of ordinary differential equations from the frequency response of a pressure transfer function using an inverse frequency algorithm. The model is formulated by dividing the line into n-sections to distribute the turbulence resistance along the line at higher Reynolds numbers. In this paper, it will be demonstrated that convergence of the analytical solution is achieved with as few as 5–10 line sections for Reynolds numbers up to 200,000. The method not only provides for the use of conventional time domain solution algorithms for ordinary differential equations but also provides empirical equations for estimating peak surge pressures and transient decay rates as defined by eigenvalues. For typical sets of line and fluid properties, the trend of the damping ratio of the first or dominate mode of the pressure transients transfer function is found to be an approximate linear function of a dimensionless parameter that is a function of the Reynolds number. In addition, a reasonably accurate dimensionless trend formula for estimates of the normalized peak pressures is formulated and presented.
Skip Nav Destination
Article navigation
June 2018
Research-Article
Water Hammer Peak Pressures and Decay Rates of Transients in Smooth Lines With Turbulent Flow
David A. Hullender
David A. Hullender
Department of Mechanical and
Aerospace Engineering,
The University of Texas at Arlington,
Arlington, TX 76019
e-mail: hullender@uta.edu
Aerospace Engineering,
The University of Texas at Arlington,
Arlington, TX 76019
e-mail: hullender@uta.edu
Search for other works by this author on:
David A. Hullender
Department of Mechanical and
Aerospace Engineering,
The University of Texas at Arlington,
Arlington, TX 76019
e-mail: hullender@uta.edu
Aerospace Engineering,
The University of Texas at Arlington,
Arlington, TX 76019
e-mail: hullender@uta.edu
Contributed by the Fluids Engineering Division of ASME for publication in the JOURNAL OF FLUIDS ENGINEERING. Manuscript received December 16, 2016; final manuscript received January 3, 2018; published online February 23, 2018. Assoc. Editor: Elias Balaras.
J. Fluids Eng. Jun 2018, 140(6): 061204 (10 pages)
Published Online: February 23, 2018
Article history
Received:
December 16, 2016
Revised:
January 3, 2018
Citation
Hullender, D. A. (February 23, 2018). "Water Hammer Peak Pressures and Decay Rates of Transients in Smooth Lines With Turbulent Flow." ASME. J. Fluids Eng. June 2018; 140(6): 061204. https://doi.org/10.1115/1.4039120
Download citation file:
Get Email Alerts
Cited By
Experimental Investigation of the Effect of Rake on a Bluff Body Equipped With a Diffuser
J. Fluids Eng (April 2025)
Related Articles
Alternative Approach for Modeling Transients in Smooth Pipe With Low Turbulent Flow
J. Fluids Eng (December,2016)
On the Propagation and Attenuation of Turbulent Fluid Transients in Circular Pipes
J. Fluids Eng (March,2016)
Analytical Non-Newtonian Oldroyd-B Transient Model for Pretransient Turbulent Flow in Smooth Circular Lines
J. Fluids Eng (February,2019)
Water Hammer Simulation in a Steel Pipeline System With a Sudden Cross Section Change
J. Fluids Eng (September,2021)
Related Proceedings Papers
Related Chapters
Antilock-Braking System Using Fuzzy Logic
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
Dynamic Behavior of Pumping Systems
Pipeline Pumping and Compression Systems: A Practical Approach
Cavitating Structures at Inception in Turbulent Shear Flow
Proceedings of the 10th International Symposium on Cavitation (CAV2018)