A novel thermal management approach is explored, which uses supercritical carbon dioxide (sCO2) as a working fluid to manage extreme heat fluxes in electronics cooling applications. In the pseudocritical region, sCO2 has extremely high volumetric thermal capacity, which can enable operation with low pumping requirements, and without the potential for two-phase critical heat flux (CHF) and flow instabilities. A model of a representative microchannel heat sink is evaluated with single-phase liquid water and FC-72, two-phase boiling R-134a, and sCO2. For a fixed pumping power, sCO2 is found to yield lower heat-sink wall temperatures than liquid coolants. Practical engineering challenges for supercritical thermal management systems are discussed, including the limits of predictive heat transfer models, narrow operating temperature ranges, high working pressures, and pump design criteria. Based on these findings, sCO2 is a promising candidate working fluid for cooling high heat flux electronics, but additional thermal transport research and engineering are needed before practical systems can be realized.
Skip Nav Destination
Article navigation
December 2016
This article was originally published in
Journal of Heat Transfer
Technical Briefs
High-Flux Thermal Management With Supercritical Fluids
Brian M. Fronk,
Brian M. Fronk
Mem. ASME
School of Mechanical,
Industrial and Manufacturing Engineering,
Oregon State University,
204 Rogers Hall,
Corvallis, OR 97331
e-mail: Brian.Fronk@oregonstate.edu
School of Mechanical,
Industrial and Manufacturing Engineering,
Oregon State University,
204 Rogers Hall,
Corvallis, OR 97331
e-mail: Brian.Fronk@oregonstate.edu
Search for other works by this author on:
Alexander S. Rattner
Alexander S. Rattner
Mem. ASME
Department of Mechanical and Nuclear Engineering,
Pennsylvania State University,
236A Reber Building,
University Park, PA 16802
e-mail: Alex.Rattner@psu.edu
Department of Mechanical and Nuclear Engineering,
Pennsylvania State University,
236A Reber Building,
University Park, PA 16802
e-mail: Alex.Rattner@psu.edu
Search for other works by this author on:
Brian M. Fronk
Mem. ASME
School of Mechanical,
Industrial and Manufacturing Engineering,
Oregon State University,
204 Rogers Hall,
Corvallis, OR 97331
e-mail: Brian.Fronk@oregonstate.edu
School of Mechanical,
Industrial and Manufacturing Engineering,
Oregon State University,
204 Rogers Hall,
Corvallis, OR 97331
e-mail: Brian.Fronk@oregonstate.edu
Alexander S. Rattner
Mem. ASME
Department of Mechanical and Nuclear Engineering,
Pennsylvania State University,
236A Reber Building,
University Park, PA 16802
e-mail: Alex.Rattner@psu.edu
Department of Mechanical and Nuclear Engineering,
Pennsylvania State University,
236A Reber Building,
University Park, PA 16802
e-mail: Alex.Rattner@psu.edu
1Corresponding author.
Contributed by the Heat Transfer Division of ASME for publication in the JOURNAL OF HEAT TRANSFER. Manuscript received September 17, 2015; final manuscript received June 24, 2016; published online August 2, 2016. Assoc. Editor: Ali Khounsary.
J. Heat Transfer. Dec 2016, 138(12): 124501 (4 pages)
Published Online: August 2, 2016
Article history
Received:
September 17, 2015
Revised:
June 24, 2016
Citation
Fronk, B. M., and Rattner, A. S. (August 2, 2016). "High-Flux Thermal Management With Supercritical Fluids." ASME. J. Heat Transfer. December 2016; 138(12): 124501. https://doi.org/10.1115/1.4034053
Download citation file:
Get Email Alerts
Cited By
On Prof. Roop Mahajan's 80th Birthday
J. Heat Mass Transfer
Thermal Hydraulic Performance and Characteristics of a Microchannel Heat Exchanger: Experimental and Numerical Investigations
J. Heat Mass Transfer (February 2025)
Related Articles
Meso Scale Pulsating Jets for Electronics Cooling
J. Electron. Packag (December,2005)
Optimized design and simulation study of liquid-cooled heat sink model for IGBT module based on TPMS structure
J. Thermal Sci. Eng. Appl (January,0001)
Effects of Dissolved Air on Subcooled Flow Boiling of a Dielectric Coolant in a Microchannel Heat Sink
J. Electron. Packag (December,2006)
Embedded Two-Phase Cooling of High Flux Electronics Via Press-Fit and Bonded FEEDS Coolers
J. Electron. Packag (September,2018)
Related Proceedings Papers
Related Chapters
Thermoelectric Coolers
Thermal Management of Microelectronic Equipment
Thermal Design Guide of Liquid Cooled Systems
Thermal Design of Liquid Cooled Microelectronic Equipment
A Dependable Answer
Hot Air Rises and Heat Sinks: Everything You Know about Cooling Electronics Is Wrong