In this article, the design and development of a biaxial tensile test device and its specimen are described. The device, which was designed for evaluating the mechanical characteristics of a thin film specimen under in-plane uniaxial and biaxial tensile stress states, consists of four sets of a piezoelectric actuator, a load cell, a linear variable differential transformer (LVDT), and an actuator case including lever structures with displacement amplification function. The structures fabricated by wire electrical discharge machining are able to amplify the actuator’s displacement by a factor of 3.8 along the tensile direction. The biaxial test specimen prepared using conventional micromachining processes is composed of a cross-shaped film section and chucking parts supported by silicon springs. After square holes in four chuck parts are respectively hooked with four loading poles, the film section is tensioned to the directions where the poles get away from the center of the specimen. Tensile strain rate can be individually controlled for each tensile direction. Raman spectroscopic stress analyses demonstrated that the developed biaxial tensile test device was able to accurately apply not only uniaxial but also biaxial tensile stress to a single-crystal silicon (SCS) film specimen.
Skip Nav Destination
e-mail: namazu@eng.u-hyogo.ac.jp
Article navigation
January 2012
Research Papers
Design and Development of a Biaxial Tensile Test Device for a Thin Film Specimen
Takahiro Namazu,
Takahiro Namazu
Associate Professor
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
e-mail: namazu@eng.u-hyogo.ac.jp
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan; PRESTO, Japan Science and Technology Agency, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012, Japan
Search for other works by this author on:
Yuji Nagai,
Yuji Nagai
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan
Search for other works by this author on:
Nobuyuki Naka,
Nobuyuki Naka
Semiconductor Systems R&D Department, HORIBA, Ltd., 2 Miyanohigashi, Kisshoin, Minami-ku, Kyoto, Kyoto 601-8510,
Japan
Search for other works by this author on:
Nozomu Araki,
Nozomu Araki
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan
Search for other works by this author on:
Shozo Inoue
Shozo Inoue
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan
Search for other works by this author on:
Takahiro Namazu
Associate Professor
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan; PRESTO, Japan Science and Technology Agency, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012, Japan
e-mail: namazu@eng.u-hyogo.ac.jp
Yuji Nagai
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan
Nobuyuki Naka
Semiconductor Systems R&D Department, HORIBA, Ltd., 2 Miyanohigashi, Kisshoin, Minami-ku, Kyoto, Kyoto 601-8510,
Japan
Nozomu Araki
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan
Shozo Inoue
Department of Mechanical and Systems Engineering, Division of Mechanical Systems,
University of Hyogo
, 2167 Shosha, Himeji, Hyogo 671-2201, Japan
J. Eng. Mater. Technol. Jan 2012, 134(1): 011009 (8 pages)
Published Online: December 8, 2011
Article history
Received:
May 23, 2011
Revised:
October 21, 2011
Online:
December 8, 2011
Published:
December 8, 2011
Citation
Namazu, T., Nagai, Y., Naka, N., Araki, N., and Inoue, S. (December 8, 2011). "Design and Development of a Biaxial Tensile Test Device for a Thin Film Specimen." ASME. J. Eng. Mater. Technol. January 2012; 134(1): 011009. https://doi.org/10.1115/1.4005348
Download citation file:
Get Email Alerts
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Strain-Modulated Adatom and Surface Vacancy Pair
Interactions
J. Appl. Mech (May,2005)
Response of Thin Films and Substrate to Micro-Scale Laser Shock Peening
J. Manuf. Sci. Eng (June,2007)
Device Process Integration: A New Device Fabrication Approach
J. Med. Devices (June,2010)
Simulation and Model Validation of the Surface Cooling System for Improving the Power of a Photovoltaic Module
J. Sol. Energy Eng (November,2011)
Related Proceedings Papers
Related Chapters
Insulating Properties of W-Doped Ga2O3 Films Grown on Si Substrate for Low-K Applications
International Conference on Advanced Computer Theory and Engineering, 4th (ICACTE 2011)
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Flexibility Analysis
Process Piping: The Complete Guide to ASME B31.3, Fourth Edition