Robust gear designs consider not only crack initiation, but crack propagation trajectories for a fail-safe design. In actual gear operation, the magnitude as well as the position of the force changes as the gear rotates through the mesh. A study to determine the effect of moving gear tooth load on crack propagation predictions was performed. Two-dimensional analysis of an involute spur gear and three-dimensional analysis of a spiral-bevel pinion gear using the finite element method and boundary element method were studied and compared to experiments. A modified theory for predicting gear crack propagation paths based on the criteria of Erdogan and Sih [18] was investigated. Crack simulation based on calculated stress intensity factors and mixed mode crack angle prediction techniques using a simple static analysis in which the tooth load was located at the highest point of single tooth contact was validated. For three-dimensional analysis, however, the analysis was valid only as long as the crack did not approach the contact region on the tooth.

Issue Section:
Technical Papers
Keywords:
fatigue cracks, finite element analysis, boundary-elements methods, failure (mechanical), reliability, stress effects, design engineering
Topics:
Crack propagation, Fracture (Materials), Gears, Simulation, Stress, Gear teeth, Boundary element methods
1.
Nicoletto
,
G.
,
1993
, “
Approximate Stress Intensity Factors for Cracked Gear Teeth
,”
Eng. Fract. Mech.
,
44
, No.
2
, pp.
231
–
242
.
2.
Abersek
,
B.
, and
Flasker
,
J.
,
1994
, “
Stress Intensity Factor for Cracked Gear Tooth
,”
Theor. Appl. Fract. Mech.
,
20
, No.
2
, pp.
99
–
104
.
3.
Sfakiotakis
,
V. G.
,
Katsareas
,
D. E.
, and
Anifantis
,
N. K.
,
1997
, “
Boundary Element Analysis of Gear Teeth Fracture
,”
Eng. Anal Boundary Elem.
,
20
, No.
2
, pp.
169
–
175
.
4.
Inoue, K., and Kato, M., 1994, “Crack Growth Resistance Due to Shot Peening in Carburized Gears,” Presented at the 30th AIAA/ASME/SAE/ASEE Joint Propulsion Conference, Indianapolis, IN.
5.
Blarasin
,
A.
,
Guagliano
,
M.
, and
Vergani
,
L.
,
1997
, “
Fatigue Crack Growth Predictions in Specimens Similar to Spur Gear Teeth
,”
Fatigue Fract. Eng. Mater. Struct.
,
20
, No.
8
, pp.
1171
–
1182
.
6.
Glodez
,
S.
,
Pehan
,
S.
, and
Flasker
,
J.
,
1998
, “
Experimental Results of the Fatigue Crack Growth in a Gear Tooth Root
,”
Int. J. Fatigue
,
20
, No.
9
, pp.
669
–
675
.
7.
Arikin, M. A., Tarhan, A. I., and Yahoj, O. S., 1998, “Life Estimate of a Spur Gear with a Tooth Cracked at Fillet Region,” Proceedings of the ASME Design Engineering Technical Conference, Atlanta, GA.
8.
Abersek
,
B.
, and
Flasker
,
J.
,
1998
, “
Experimental Analysis of Propagation of Fatigue Crack on Gears
,”
Exp. Mech.
,
38
, No.
3
, pp.
226
–
230
.
9.
Lewicki
,
D. G.
, and
Ballarini
,
R.
,
1997
, “
Effect of Rim Thickness on Gear Crack Propagation Path
,”
ASME J. Mech. Des.
,
119
, No.
1
, pp.
88
–
95
.
10.
Pehan
,
S.
,
Hellen
,
T. K.
,
Flasker
,
J.
, and
Glodez
,
S.
,
1997
, “
Numerical Methods for Determining Stress Intensity Factors vs Crack Depth in Gear Tooth Roots
,”
Int. J. Fatigue
,
19
, No.
10
, pp.
677
–
685
.
11.
Curtin, T. J., Adey, R. A., Baynham, J. M. W., and Marais, P., 1998, “Fatigue Crack Growth Simulation for Complex Three-Dimensional Geometry and Loaded,” Proceedings from the 2nd Joint NASA/FAA/DoD Conference on Aging Aircraft, Williamsburg, VA.
12.
Lewicki, D. G., Sane, A. D., Drago, R. J., and Wawrzynek, P. A., 1999, “Three-Dimensional Gear Crack Propagation Studies,” Proceedings of the 4th World Congress on Gearing and Power Transmission, Paris, France, 3, pp. 2311–2324.
13.
Ciavarella
,
M.
, and
Demelio
,
G.
,
1999
, “
Numerical Methods for the Optimization of Specific Sliding, Stress Concentration, and Fatigue Life of Gears
,”
Int. J. Fatigue
,
21
, No.
5
, pp.
465
–
474
.
14.
Wawrzynek, P. A., 1991, “Discrete Modeling of Crack Propagation: Theoretical Aspects and Implementation Issues in Two and Three Dimensions,” Ph.D. Dissertation, Cornell University.
15.
Rice
,
J. R.
,
1968
, “
A Path Independent Integral and the Approximate Analysis of Strain Concentration by Notches and Cracks
,”
ASME J. Appl. Mech.
,
35
, pp.
379
–
386
.
16.
Lin
,
H. H.
,
Huston
,
R. L.
, and
Coy
,
J. J.
,
1988
, “
On Dynamic Loads in Parallel Shaft Transmissions: Part I—Modeling and Analysis
,”
ASME J. Mech., Transm., Autom. Des.
,
110
, No.
2
, pp.
221
–
225
.
17.
Williams
,
M. L.
,
1957
, “
On the Stress Distribution at the Base of a Stationary Crack
,”
ASME J. Appl. Mech.
,
24
, No.
1
, pp.
109
–
114
.
18.
Erdogan
,
F.
, and
Sih
,
G. C.
,
1963
, “
On the Crack Extension in Plates Under Plane Loading and Transverse Shear
,”
J. Basic Eng.
,
85
, pp.
519
–
527
.
19.
Spievak, L. E., 1999, “Simulating Fatigue Crack Growth in Spiral Bevel Gears,” M. Sc. thesis, Cornell University.
20.
Handschuh, R. F., and Litvin, F. L., 1991, “A Method for Determining Spiral-Bevel Gear Tooth Geometry for Finite Element Analysis,” NASA TP-3096, AVSCOM TR-91-C-020.
21.
Litvin
,
F. L.
, and
Zhang
,
Y.
,
1991
, “
Local Synthesis and Tooth Contact Analysis of Face-Milled Spiral Bevel Gears,” NASA Contractor Report 4342, AVSCOM Technical Report
90-C-028.
22.
Handschuh
,
R. F.
, and
Kicher
,
T. P.
,
1996
, “
A Method for Thermal Analysis of Spiral Bevel Gears
,”
ASME J. Mech. Des.
,
118
, No.
4
, pp.
580
–
585
.
23.
Paris
,
P. C.
, and
Erdogen
,
F.
,
1963
, “
A Critical Analysis of Crack Propagation Laws
,”
J. Basic Eng.
,
85
, pp.
528
–
534
.
24.
Au, J. J., and Ke, J. S., 1981, “Correlation Between Fatigue Crack Growth Rate and Fatigue Striation Spacing in AISI 9310 (AMS 6265) Steel,” Fractography and Material Science, ASTM STP 733, pp. 202–221.
Copyright © 2001
 by ASME
You do not currently have access to this content.