Abstract

High temperature (⁠>300°F⁠, 149°C⁠) water has been found to greatly accelerate fatigue crack growth rates in carbon and low-alloy steels. Current ASME Code fatigue design curves are based entirely on data obtained in air. While a factor of 2 on life was applied to the air data to account for environmental effects, the actual effects have been found to be an order of magnitude greater in the low-cycle regime. A great deal of work has been carried out on these environmental effects by talented investigators worldwide. The ASME Code Subgroup on Fatigue Strength has been working for 20years on the development of new fatigue design methods and curves to account for high temperature water environmental effects. This paper presents an overview of the data and analyses used to formulate proposed new environmental fatigue design curves, which maintain the same safety margins as existing Code fatigue design curves for air environments, and a historical summary of ASME Code Work in this field.

Issue Section:
Technology Reviews
Keywords:
alloy steel, carbon steel, environmental factors, fatigue cracks, standards
Topics:
Alloys, ASME Standards, Carbon, Fatigue, Fatigue design, Fatigue strength, Fracture (Materials), Steel, Water, Fatigue cracks, Cycles, High temperature

References

1.
“
Tentative Structural Design Basis for Reactor Pressure Vessels and Directly Associated Components (Pressurized, Water Cooled Systems)
,” Dated Dec. 1, 1958, Updated in 1963.
2.
“
Criteria of Sec. III of the ASME Boiler and Pressure Vessel Code for Nuclear Vessels
,” Published by the ASME, 1963;
“
Sec. VIII, Div. 2 of the ASME Boiler and Pressure Vessel Code, Guide to Alternate Rules for Pressure Vessels
,” Published by the ASME, 1968;
“
Criteria of the ASME Boiler and Pressure Vessel Code for Design by Analysis in Secs. III and VIII, Div. 2
,” Published by the ASME, 1969.
3.
Langer
,
B. F.
, 1958, “
Design Value for Thermal Stress in Ductile Materials
,”
Weld. J. Res. Suppl.
,
37
, p.
411
.
4.
Langer
,
B. F.
, 1962, “
Design of Pressure Vessels for Low-Cycle Fatigue
,”
ASME J. Basic Eng.
0021-9223,
3
, pp.
389
–
482
.
5.
VanDerSluys
,
W. A.
, 2003, “
PVRC’s Position on Environmental Effects on Fatigue Life in LWR Applications
,”
Weld. Res. Counc. Bull.
0043-2326,
487
, pp.
1
–
59
.
6.
Hale
,
D. H.
,
Wilson
,
S. A.
,
Kass
,
J. W.
, and
Kiss
,
E.
, 1981, “
Low Cycle Fatigue of Commercial Piping Steels in a BRW Primary Water Environment
,”
ASME J. Eng. Mater. Technol.
0094-4289,
103
, pp.
15
–
25
.
Crossref
Search ADS
 
7.
Weinstein
,
D.
, 1982, “
BWR Environmental Cracking Margins for Carbon Steel Piping
,” EPRI Report No. NP-2406.
8.
Mindlin
,
H.
 et al., 1986, “
EPRI Data Base for Environmentally-Assisted Cracking (EDEAC)
,” EPRI Report No. NP-4485.
9.
Eason
,
E. D.
,
Nelson
,
E. E.
, and
Gilman
,
J. D.
, 1994, “
Technical Basis for a Revised Fatigue Crack Growth Rate Reference Curve for Ferritic Steels in Light Water Reactor Environments
,”
Changing Priorities of Codes and Standards
,
ASME
,
New York
, pp.
81
–
89
, PVP-Vol.
286
.
10.
Eason
,
E. D.
,
Nelson
,
E. E.
, and
Gilman
,
J. D.
, 1994, “
Modeling of Fatigue Crack Growth Rate for Ferritic Steels in Light Water Reactor Environments
,”
Changing Priorities of Codes and Standards
,
ASME
,
New York
, pp.
131
–
142
, PVP-Vol.
286
.
Crossref
Search ADS
 
11.
Higuchi
,
M.
, and
Iida
,
K.
, 1991, “
Fatigue Strength Correction Factors for Carbon and Low-Alloy Steels in Oxygen-Containing High-Temperature Water
,”
Nucl. Eng. Des.
0029-5493,
129
, pp.
293
–
306
.
Crossref
Search ADS
 
12.
Chopra
,
O. K.
, and
Shack
,
W. J.
, 2003, “
Margins for ASME Code Fatigue Design Curve Effects of Surface Finish and Material Variability
,”
ASME PVP Conference
,
Cleveland, OH
, Jul.
24
, PVP 2003-1772.
Crossref
Search ADS
 
13.
O’Donnell
,
T. P.
, and
O’Donnell
,
W. J.
, 1995, “
Cyclic Rate Dependent Fatigue Life in Reactor Water
,”
Fatigue and Crack ASME Pressure Vessel and Piping Conference
,
Honolulu, HI
, Growth: Environmental Effects Modeling Studies and Design Considerations, pp.
59
–
69
.
14.
O’Donnell
,
T. P.
, and
O’Donnell
,
W. J.
, 1996, “
J-Integral Values for Cracks in Conventional Fatigue Specimens
,”
Pressure Vessel and Piping Codes and Standards
,
presented at the ASME Pressure Vessel and Piping Conference
,
Montreal, Canada
, Jul. 21–28, PVP Vol.
339-2
, pp.
199
–
201
.
15.
Maneschy
,
E.
,
O’Donnell
,
W. J.
, and
O’Donnell
,
T. P.
, 1998, “
J-Integrals for Cyclic Loading
,”
Fatigue, Environmental Factors and New Materials
,
ASME
,
New York
, PVP Vol.
374
.
16.
Jones
,
D. P.
,
Eason
,
E. D.
, and
Friedman
,
E.
, 1994, “
Proposal to Incorporate Updated Fatigue Crack Growth Rate Curves for Ferritic Steels in Water environments Into Appendix A of Section III and VIII
,” developed by the PVRC Working Group on da/dN Data Analysis, Rev. 7, May.
17.
Chopra
,
O. K.
, and
Shack
,
W. J.
, 1995, “
Effects of LWR Environments on Fatigue Life of Carbon and Low Alloy Steels
,”
Fatigue and Crack Growth: Environmental Effects, Modeling Studies, and Design Considerations
,
ASME
,
New York
, PVP Vol.
306
.
18.
Jaske
,
C. E.
, and
O’Donnell
,
W. J.
, 1977, “
Fatigue Design Criteria for Pressure Vessel Alloys
,”
ASME J. Pressure Vessel Technol.
0094-9930,
99
(
4
), pp.
584
–
592
.
Crossref
Search ADS
 
19.
Cooper
,
W. E.
, 1992, “
The Initial Scope and Intent of the Sec. III Fatigue Design Procedures
,”
PVRC Workshop on Environmental Effects on Fatigue Performance
,
Clearwater Beach, FL
, Jan. 20.
20.
O’Donnell
,
T. P.
, and
O’Donnell
,
W. J.
, 1995, “
Stress Intensity Values in Conventional S-N Fatigue Specimens
,”
International Journal of Pressure Vessels and Piping Codes and Standards
,
ASME Pressure Vessel and Piping Conference
,
Honolulu, HI
, PVP-Vol.
313–1
, pp.
195
–
197
.
21.
O’Donnell
,
W. J.
, 1988, “
Synthesis of S-N and da/dN Life Evaluation Technologies
,”
presented at the American Society of Mechanical Engineers, Pressure Vessel and Piping Conference
,
Pittsburgh, PA
, PVP Vol.
10
.
Copyright © 2009
 by American Society of Mechanical Engineers
You do not currently have access to this content.