Abstract

The primary objective of this paper is to depict the mechanical behavior of welded and unwelded high-density polyethylene (HDPE), pipes to provide the designer with reliable design data relevant to practical applications. Therefore, it is necessary to study the effect of strain rate and specimen configuration on the mechanical behavior of welded and unwelded pipes made from HDPE. Tensile tests are conducted on specimens longitudinally cut from the pipe with thickness (10 and 30 mm), at different crosshead speeds (5–500 mm/min), and different gauge lengths (20, 25, and 50 mm) to investigate the mechanical properties of welded and unwelded specimens. All tests are performed at room temperature (Ta = 23 °C). Butt fusion, BF, welding method is used to join the different parts of HDPE pipes. The present results showed that the mechanical characteristics of welded specimens are lower than those of unwelded specimens. In the case of test specimens taken from unwelded pipe, the results of mechanical characteristics revealed that a necking phenomenon before failure appears at different locations along the gauge section. On the other hand, the fracture of welded specimens almost occurs at the fusion zone. It is found that the crosshead speed and specimen configurations have a significant effect on the mechanical behavior of both welded and unwelded specimens.

Issue Section:
Materials and Fabrication
Keywords:
butt fusion (BF) welding, high-density polyethylene (HDPE), mechanical behavior, specimen configuration, loading rate, welded and unwelded specimen
Topics:
Gages, Mechanical properties, Pipes, Stress-strain curves, Welding, Yield strength, Density, Failure, Temperature, Mechanical behavior, Polyethylene pipes, Wall thickness

References

1.
Dasari
,
A.
, and
Misra
,
R. D. K.
,
2003
, “
On the Strain Rate Sensitivity of High Density Polyethylene and Polypropylenes
,”
Mater. Sci. Eng. A
,
358
(
1–2
), pp.
356
–
371
.10.1016/S0921-5093(03)00330-7
2.
El-Bagory, T. M. A., 2010, “Failure Analysis of Polymeric Miter Pipe Bends Under Combined Loading,” Ph.D. thesis, Faculty of Engineering Mattaria, Helwan University, Cairo, Egypt.
3.
Chang
,
P. H.
, and
Teng
,
T. L.
,
2004
, “
Numerical and Experimental Investigations on the Residual Stresses of the Butt–Welded Joints
,”
Comput. Mater. Sci.
,
29
(
4
), pp.
511
–
522
.10.1016/j.commatsci.2003.12.005
4.
Popelar
,
C. F.
,
1989
, “
Characterization of Mechanical Properties for Polyethylene Gas Pipe Materials
,” M.Sc. thesis,
Graduate School of the Ohio State University
, Columbus, OH. 
5.
Greco
,
R.
,
Mucciariello
,
G.
,
Ragosta
,
G.
, and
Martuscelli
,
E.
,
1980
, “
Properties of Polyethylene–Propylene Blends—Part 1: Thermal Swelling and Mechanical Characterization of Extruded Unoriented Specimens
,”
J. Mater. Sci.
,
15
(
4
), pp.
845
–
853
.10.1007/BF00552093
6.
Tang
,
M.
,
Greco
,
R.
,
Ragosta
,
G.
, and
Cimmino
,
S.
,
1983
, “
Properties of Polyethylene-Propylene Blends—Part 3: Mechanical Characterization of Ultradrawn Fibres
,”
J. Mater. Sci.
,
18
(
4
), pp.
1031
–
1038
.10.1007/BF00551971
7.
Dusunceli
,
N.
, and
Colak
,
O. U.
,
2008
, “
The Effects of Manufacturing Techniques on Viscoelastic and Viscoplastic Behavior of High Density Polyethylene (HDPE)
,”
Mater. Des.
,
29
(
6
), pp.
1117
–
1124
.10.1016/j.matdes.2007.06.003
8.
Barber
,
P.
, and
Atkinson
,
J. R.
,
1974
, “
The Use of Tensile Tests to Determine the Optimum Conditions for Butt Fusion Welding Certain Grades of Polyethylene, Polybutene–1 and Polypropylene Pipes
,”
J. Mater. Sci.
,
9
(
9
), pp.
1456
–
1466
.10.1007/BF00552931
9.
Tariq, F., Naz, N., Khan, M. A., and Baloch, R. A., 2012, “Failure Analysis of High Density Polyethylene Butt Weld Joint”
J. Failure Anal. Prev.
, 12, pp. 168–180.10.1007/s11668-011-9536-y
10.
Nishimura
,
H.
, and
Narisawa
,
I.
,
1991
, “
Evaluation of Impact Properties of Butt Fusion–Jointed Medium–Density Polyethylene Pipes for Gas Distribution
,”
Polymer
,
32
(
12
), pp.
2199
–
2204
.10.1016/0032-3861(91)90046-L
11.
Decourcy
,
D. R.
, and
Atkinson
,
J. R.
,
1977
, “
The Use of Tensile Tests to Determine the Optimum Conditions for Butt Welding Polyethylene Pipes of Different Melt Flow Index
,”
J. Mater. Sci.
,
12
(
8
), pp.
1535
–
1551
.10.1007/BF00542804
12.
Wilson
,
K. A.
,
1995
, “
Verification of Butt Fusion Weld Quality in Large Diameter PE100 Water Pipes
,”
Proceedings of the Ninth International Conference on Plastics Pipes
, Edinburgh, UK, Sept. 18–21, pp.
168
–
180
.
13.
Chen
,
H.
,
Scavuzzo
,
R. J.
, and
Srivatsan
,
T. S.
,
1997
, “
Influence of Joining on the Tensile Behavior of High Density Polyethylene Pipe
,”
J. Mater. Sci.
,
16
, pp.
897
–
898
.10.1023/A:1018579903455
14.
Chen
,
H.
,
Scavuzzo
,
R. J.
, and
Srivatsan
,
T. S.
,
1997
, “
Influence of Joining on the Fatigue and Fracture Behavior of High Density Polyethylene Pipe
,”
J. Mater. Sci. Perform.
,
6
(
4
), pp.
473
–
480
.10.1007/s11665-997-0119-8
15.
Daigle
,
L.
,
Zhao
,
J. Q.
, and
Beaulieu
,
D.
,
2003
, “
Innovative Approach to Testing the Quality of Fusion Joints
,”
Plast., Rubber Compos.
,
32
(
8–9
), pp.
385
–
395
.10.1179/146580103225004153
16.
Zhao
,
J. Q.
,
Daigle
,
L.
, and
Beaulieu
,
D.
,
2002
, “
Effect of Joint Contamination on the Quality of Butt–Fused High–Density Polyethylene (HDPE) Pipe Joints
,”
Can. J. Civ. Eng.
,
29
(
5
), pp.
787
–
798
.10.1139/l02-078
17.
Leskovics
,
K.
,
Kollar
,
M.
, and
Barczy
,
P.
,
2006
, “
A Study of Structure and Mechanical Properties of Welded Joints in Polyethylene Pipes
,”
Mater. Sci. Eng. A
,
419
(
1–2
), pp.
138
–
143
.10.1016/j.msea.2005.12.019
18.
El-Bagory
,
T. M. A. A.
,
Alkanhal
,
T. A. R.
, and
Younan
,
M. Y. A.
,
2015
, “
Effect of Specimen Geometry on the Predicted Mechanical Behavior of Polyethylene Pipe Material
,”
ASME J. Pressure Vessel Technol.
,
137
(
6
), p.
061202
.10.1115/1.4029795
19.
El-Bagory
,
T. M. A. A.
,
Sallam
,
H. E. M.
, and
Younan
,
M. Y. A.
,
2014
, “
Effect of Strain Rate, Thickness, Welding on the J-R Curve for Polyethylene Pipe Materials
,”
Theor. Appl. Fract. Mech.
,
74
, pp.
164
–
180
.10.1016/j.tafmec.2014.09.008
20.
El-Bagory
,
T. M. A. A.
,
Sallam
,
H. E. M.
,
Younan
,
M. Y. A.
, and
Abdel- Latif
,
L. A.
,
2014
, “
Limit Load Determination and Material Characterization of Cracked Polyethylene Miter Pipe Bends
,”
ASME J. Pressure Vessel Technol.
,
136
(
4
), p.
041203
.10.1115/1.4026330
21.
El-Bagory
,
T. M. A. A.
,
Sallam
,
H. E. M.
, and
Younan
,
M. Y. A.
,
2015
, “
Evaluation of Fracture Toughness Behavior of Polyethylene Pipe Materials
,”
ASME J. Pressure Vessel Technol.
,
137
(
6
), p.
061402
.10.1115/1.4029925
22.
EL-Bagory
,
T. M.
,
Younan
,
M. A.
,
Sallam
,
H. E. M.
, and
Abdel-Latif
,
L. A.
,
2013
, “
Plastic Load of Precracked Polyethylene Miter Pipe Bends Subjected to in-Plane Bending Moment
,”
ASME J. Pressure Vessel Technol.
,
135
(
6
), p.
061203
.10.1115/1.4024658
23.
EL-Bagory
,
Younan
,
M. A.
, and
Alarifi
,
I. M.
,
2018
, “
Failure Analysis of Ring Hoop Tension Test (RHTT) Specimen Under Different Loading Conditions
,”
ASME
Paper No. PVP 2018-84198.10.1115/PVP 2018-84198
24.
ASTM
,
2016
, “
Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
,” Annual Book of ASTM Standards, Part 08.04, Plastic Pipe and Building Products, ASTM International, West Conshohocken, PA, Standard No.
D2122-2016
.10.1520/D2122-16
25.
Potente
,
H.
, and
Tappe
,
P.
,
1984
, “
Heated Tool–Butt Welding of Polyethylene-Pipes–Welding Parameters and Testing Technique
,”
Mater. Des.
,
5
(
6
), pp.
273
–
280
.10.1016/0261-3069(85)90112-8
26.
Stokes
,
V. K.
,
1998
, “
Experiments on the Hot-Tool Welding of Three Dissimilar Thermoplastics
,”
Polymer
,
39
(
12
), pp.
2469
–
2477
.10.1016/S0032-3861(97)00569-7
27.
DVS,
2015
, “
Welding of Thermoplastics—Heated Tool Welding of Pipes, Pipeline Components and Sheets Made of PE
,” DVS, German Institute for Standardization, (Deutsches Institut für Normung) (DIN), Düsseldorf, Germany, No.
DVS 2207-1:2015
.https://infostore.saiglobal.com/en-us/Standards/DVS-2207-1-2015-492261_SAIG_DVS_DVS_1102248/
28.
ASTM,
2016
, “
Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
,” Annual Book of ASTM Standards, Part 08.04, Plastic Pipe and Building Products, ASTM International, West Conshohocken, PA, Standard No.
D3261
.10.1520/D3261-16
29.
ASTM
, 2019, “
Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings
,” Annual Book of ASTM Standards, Part 08.04, Plastic Pipe and Building Products, ASTM International, West Conshohocken, PA, Standard No.
F2620-13
. 10.1520/F2620-13
30.
British Standard,
2011
, “
Methods of Testing Plastics
,” British Standard Institution, London, UK, Standard No.
BS 2782–0
.https://standards.globalspec.com/std/1400367/BS%202782-0
31.
ASTM
,
2014
, “
Standard Test Method for Tensile Properties of Plastics (Metric)
,” Annual Book of ASTM Standards, Part 08.01, Plastics-General Test Method, ASTM International, West Conshohocken, PA, Standard No.
D638
, pp.
59
–
67
.10.1520/D0638-14
32.
DIN,
1981
, “
Testing of Plastics–Tensile Test
,”
DIN, German Institute for Standardization, (Deutsches Institut für Normung) (DIN), Düsseldorf, Germany, Standard No.
DIN 53455
, pp.
1
–
7
.https://infostore.saiglobal.com/en-us/Standards/DIN-53455-1981-408268_SAIG_DIN_DIN_924702/
33.
Arridge
,
R. G. C.
,
1975
,
Mechanics of Polymers
,
Clarendon Press
,
London
.
34.
Che
,
M.
,
Grellmann
,
W.
, and
Seidler
,
S.
,
1997
, “
Crack Resistance Behavior of Polyvinyl Chloride
,”
J. Appl. Polym. Sci.
,
64
(
6
), pp.
1079
–
1090
.10.1002/(SICI)1097-4628(19970509)64:6<1079::AID-APP7>3.0.CO;2-I
Copyright © 2021 by ASME
You do not currently have access to this content.