The offshore industry has presented an increasing demand over the last few decades, requiring the production in deep water fields. The end fittings (EF) are critical points within the production system. Therefore, structural and fatigue analyses are essential in the EF design, making it necessary to know the stress distribution experienced by the armor wires along the EF. Numerical and analytical models are often used in order to assess the stress state. However, characteristics like geometries, materials and interactions must be previously known in order to apply these models. The purpose of this work was to analyze the arithmetic mean surface roughness (Ra) and to determine the friction coefficient (μ) for two types of armor wires when in contact with resin used to fill the EF. The resin used in the interaction with the armor wires was an epoxy filled with metallic particles. For the experimental analysis straight carbon steel armor wires with different cross-sections, typically used in 2.5″ and 8″ flexible pipes were used. Surface profile was obtained for each wire by repeated measurements along two lines over each surface. A total of three repetitions were performed in each measure line. Longitudinal roughness was determined through these profiles. Finally, friction coefficients were obtained experimentally by means of a device that allows to simulate the wire pullout and sliding process. In this device, two epoxy pads were put in contact with the surface of the analyzed wire sample, and rigid bodies in contact with the pads were used to ensure that the normal load applied is transmitted uniformly through the contact surface. The displacement rate, contact pressure between the surface of the wire and the epoxy resin pads, and axial force were recorded. The roughness in the longitudinal direction of the wires was analyzed through descriptive statistic and compared by Student’s “t” test. The highest values were obtained on wires with larger sections. This behavior is exposed on the results obtained for the friction coefficient as a function of the contact pressure. Friction coefficient for both wires was analyzed and compared using a Mann-Whitney U test. Both friction coefficients have a positive slope, indicating a small increase as the contact pressure raise. The significance value obtained for the means comparisons was p = 0.0001 and confirms that the average friction coefficient of the two wires are really different. Because of that, we conclude that is necessary to treat the EF project for different flexible pipes differentially.

In this work, a bidimensional finite element (FE) approach is proposed to estimate the stresses induced in the tensile armor wires inside end fittings (EF) of flexible pipes. This approach accounts for the residual stresses caused by the mounting procedure and the deformed configuration of the wire. The resin and its interaction with the wires are also addressed. A parametric study was performed aiming at investigating the influence of three parameters on the stress state along the wire, i. e. , the contact conditions between the resin and the wire inside the EF, the stress levels induced during the factory acceptance test (FAT) or the offshore leak test (OLT) and the resin elastic properties. The study pointed that high stress concentration is induced in the transition between the flexible pipe’s body and the EF and the stress distribution along the wire may be significantly affected by these parameters. Moreover, the apparent axial stiffness of the wire is also modified by its anchoring conditions, which may lead to non-uniform stress distributions among the wires of the tensile armor layers.

The structural behavior of the flexible pipe tensile armors inside the end fitting (EF) is different from the one observed in the pipe body. The actual design methodology shows that the end fitting of the riser top section (at the interface with the floating unit) is critical with respect to fatigue, as stress concentration that occurs in this region during the end fitting assembly leading to significant plastic strains. Aiming at improving the structural performance of flexible risers, Petrobras designed and patented a novel concept of flexible pipe end fitting in which its assembly can be carried out without the need of folding the tensile armor thus avoiding the introduction of plastic strains and residual stresses in this layer. In order to assess and quantify the benefits of this new concept, in this work, a comparative study between the current end fitting concept used by the industry and the new technology proposed by Petrobras was conducted. This study comprises not only the stress distribution along the wire inside the end fitting but also the fatigue performance. For this purpose, finite element analyses have been carried out considering the entire end fitting mounting process and also the operational loads. These analyses were calibrated with results from midscale tests in which a longitudinal slice of the real end fitting was simulated. An instrumented tensile armor wire was embedded in the resin epoxy and pulled out from a test device. The results obtained show that the using of the proposed technology results in a considerably end fitting fatigue performance improvement.