The thermal management of power electronics presents a significant challenge to thermal engineers due to high power loads coupled with small footprints. Inadequate thermal dissipation of these loads can lead to excessively high equipment temperatures and subsequent system failure. In this study, a unique power electronics-based transformer, called the intelligent universal transformer (IUT), is thermally analyzed using the computational fluid dynamics software ICEPAK. The objective of this work is to examine the use of a finned heat pipe array for the power electronics in the IUT. A design sensitivity study was performed to determine the effect of the number of fins attached to the heat pipe array, the number of heat pipes in the heat pipe array, and the fin material on the steady-state operating temperature of the power electronics. It was determined that a set of 33 copper fins attached to an array of 36 heat pipes on each side of the containment unit is sufficient for continuous operation of the power electronics. This analysis and thermal management solution will be applicable not only to this situation but also to other high density power electronics applications.

1.
Warzoha
,
R. J.
,
Fleischer
,
A. S.
,
Bird
,
S. D.
,
Gandhi
,
M.
, and
Sundaram
,
A.
, 2009, “
A Computational Study of the Thermal Performance of a 69kV/3000A Solid-State Current Limiter Under Transient Fault Current Loading
,”
Proceedings of the ASME InterPack Conference 2009, IPACK2009
, San Francisco, CA, Vol.
2
, pp.
693
699
.
2.
Lu
,
T. J.
, 2000, “
Thermal Management of High Power Electronics With Phase Change Cooling
,”
Int. J. Heat Mass Transfer
0017-9310,
43
(
13
), pp.
2245
2256
.
3.
North
,
M. T.
, and
Avedisian
,
C. T.
, 2000, “
Heat Pipes for Cooling High Flux/High Power Semiconductor Chips
,”
ASME J. Electron. Packag.
1043-7398,
26
(
11
), pp.
30
38
.
4.
Chiriac
,
V. A.
, 2009, “
Advanced Cooling With Embedded Heat Pipes for High Power Microelectronics
,”
Proceedings of the ASME InterPack Conference 2009, IPACK2009
, San Francisco, CA, Vol.
2
, pp.
769
776
.
5.
Ivanova
,
M.
,
Avenas
,
Y.
,
Schaffer
,
C.
,
Dezord
,
J. B.
, and
Schulz-Harder
,
J.
, 2006, “
Heat Pipe Integrated Direct Bond Copper (DBC) Technology for Cooling of Power Electronics Package
,”
IEEE Trans. Power Electron.
0885-8993,
21
(
6
), pp.
1541
1547
.
6.
Xie
,
X. L.
,
He
,
Y. L.
,
Tao
,
W. Q.
, and
Yang
,
H. W.
, 2008, “
An Experimental Investigation on a Novel High-Performance Integrated Heat Pipe-Heat Sink for High-Flux Chip Cooling
,”
Appl. Therm. Eng.
1359-4311,
28
(
5–6
), pp.
433
439
.
7.
Wei
,
X. J.
, and
Joshi
,
Y.
, 2006, “
Microchannel Heat Sinks for Electronics Cooling, a Review
,”
Proceedings of the ASME Heat and Mass Transfer Conference
, Guwahati, India, Jan. 4–6, pp.
2407
2416
.
8.
McGlen
,
R. J.
,
Jachuck
,
R.
, and
Lin
,
S.
, 2004, “
Integrated Thermal Management Techniques for High Power Electronic Devices
,”
Appl. Therm. Eng.
1359-4311,
24
(
8–9
), pp.
1143
1156
.
9.
McGranaghan
,
M.
, 2009, “
Intelligent Universal Transformer Design and Applications
,”
CIRED
, Prague, June, p.
5
.
10.
Prasher
,
R. S.
, 2003, “
A Simplified Conduction Based Modeling Scheme for Design Sensitivity Study of Thermal Solution Utilizing Heat Pipe and Vapor Chamber Technology
,”
ASME J. Electron. Packag.
1043-7398,
125
(
3
), pp.
378
385
.
11.
Chesser
,
J. B.
,
Peterson
,
G. P.
, and
Lee
,
S.
, 2000, “
A Simplified Method for Determining the Capillary Limitation of Flat Plate Heat Pipes in Electronic Cooling Applications
,”
Proceedings of the 34th National Heat Transfer Conference
, Pittsburgh, PA, Aug. 20–22.
12.
Tu
,
J.
,
Yeoh
,
G. H.
, and
Liu
,
C.
, 2008,
Computational Fluid Dynamics
,
Buttersworth-Heinemann
,
Burlington, MA
, pp.
250
258
.
13.
Wilcox
,
D. C.
, 1995,
Turbulence Modeling for CFD
,
DCW Industries
,
.
14.
Patankar
,
S. V.
, 1980,
Numerical Heat Transfer and Fluid Flow
,
Hemisphere
,
New York
, pp.
67
68
.