The effect of Al2O3 nanofluids in a corrugated plate heat exchanger (PHE) were investigated in this study using computational fluid dynamics (CFD). Nanofluids have received attention recently as potential fluids to increase heat transfer in simple geometries, and work to investigate nanofluids in different systems is ongoing. In this study, a three-channel corrugated PHE with a width of 127 mm, length of 56 mm and channel thickness of 2 mm was investigated. The hot fluid in the system flows through the middle channel while the cold fluid flows through the two side channels. Three chevron angle configurations were considered for the simulation: 60 deg/60 deg, 27 deg/60 deg, and 27 deg/27 deg. Commercially available CFD software (ansys fluent) was used for the simulations. Numerical simulations were conducted for four Al2O3-water nanofluid concentrations: 1%, 2%, 3%, and 4% by volume. In addition, plain water was simulated for comparison. The simulation results show that although the thermal conductivity does increase with increasing nanofluid volume fraction, heat transfer decreases slightly with increasing nanofluid volume fraction. This decrease can be attributed to increased fluid viscosity with increasing volume fraction and the complex flow regimes of nanofluids in the three-dimensional geometries of PHEs.
Skip Nav Destination
Article navigation
March 2013
Research-Article
Heat Transfer and Fluid Flow Analysis of Nanofluids in Corrugated Plate Heat Exchangers Using Computational Fluid Dynamics Simulation
Steven P. O'Halloran
Steven P. O'Halloran
Mechanical Engineering Department,
University of Portland
,Portland, OR 97203
Search for other works by this author on:
Amir Jokar
Steven P. O'Halloran
Mechanical Engineering Department,
University of Portland
,Portland, OR 97203
1Corresponding author.
Manuscript received December 12, 2011; final manuscript received September 10, 2012; published online February 22, 2013. Assoc. Editor: Arun Muley.
J. Thermal Sci. Eng. Appl. Mar 2013, 5(1): 011002 (10 pages)
Published Online: February 22, 2013
Article history
Received:
December 12, 2011
Revision Received:
September 10, 2012
Citation
Jokar, A., and O'Halloran, S. P. (February 22, 2013). "Heat Transfer and Fluid Flow Analysis of Nanofluids in Corrugated Plate Heat Exchangers Using Computational Fluid Dynamics Simulation." ASME. J. Thermal Sci. Eng. Appl. March 2013; 5(1): 011002. https://doi.org/10.1115/1.4007777
Download citation file:
Get Email Alerts
Evaluation of Component Level Degradation in the Boeing 737-800 Air Cycle Machine
J. Thermal Sci. Eng. Appl (March 2023)
Analysis and Optimization of Heat Dissipation Module in the Motor Grader Engine Compartment
J. Thermal Sci. Eng. Appl (March 2023)
Study on the exergy transfer characteristics of the heat transfer process of the tube heating furnace
J. Thermal Sci. Eng. Appl
Related Articles
Numerical Study of Thermofluid Characteristics of a Double Spirally Coiled Tube Heat Exchanger
J. Thermal Sci. Eng. Appl (August,2019)
Comparative Study of Thermal and Hydraulic Performance of Three-Fluid Tubular Heat Exchanger With CuO–Water Nanofluid: Single-Phase and Multi-Phase Approaches
J. Thermal Sci. Eng. Appl (June,2021)
Heat Transfer Analysis of Cu–Water Nanofluid in a District Cooling Chilled Water Loop
J. Thermal Sci. Eng. Appl (May,2022)
Comparative Thermal Performance Analysis on Helical Screw Insert in Tube With Number of Strips With Nanofluid at Laminar Flow Regime
J. Thermal Sci. Eng. Appl (February,2021)
Related Proceedings Papers
Related Chapters
Hydrodynamic Mass, Natural Frequencies and Mode Shapes
Flow-Induced Vibration Handbook for Nuclear and Process Equipment
Threshold Functions
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Engineering and Physical Modeling of Power Plant Cooling Systems
Thermal Power Plant Cooling: Context and Engineering