Abstract
Planar movable tooth drives have a compact structure. However, as the size decreases, the heat dissipation capacity decreases; therefore, temperature control is required. A heat conduction model of the drive system, including the central wheel and movable tooth, is established, and the meshing point of the movable tooth and center wheel is considered the heat source. The heat flux density at the meshing point is determined, and the analytical equations describing the temperature increases of the center wheel and the movable tooth are derived. The effects of the input power and system parameters on the temperature increase of the system are analyzed. The results show that the temperature difference of the movable tooth is about 1.5 times the temperature of the center wheel, and the temperature increase near the heat source decreases by more than 15 °C as the movable tooth radius increases from 2 mm to 2.5 mm. The movable tooth radius and center distance have significant effects on the temperature increase and can be used as control parameters to prevent a temperature increase of the drive.
References
1.
Keith
, S.
, 1982
, Subtractive and Additive Differential Gear Reduction System
, US Patent No. 4338830A.2.
Terada
, H.
, Makino
, H.
, and Imase
, K.
, 1988
, “Fundamental Analysis of Cycloid Ball Reducer (1st Report) Motion Principle
,” JSPE
, 12
(54
), pp. 2101
–2106
. 10.2493/jjspe.54.21013.
Terada
, H.
, Makino
, H.
, and Imase
, K.
, 1990
, “Fundamental Analysis of Cycloid Ball Reducer (2nd Report) Radius of Curvature and Pressure Angle
,” JSPE
, 56
(4
), pp. 751
–756
. 10.2493/jjspe.56.7514.
Kenji
, I.
, 1997
, Ball-rolling type torque Transmission Device
, US Patent No. 5683323A.5.
Terada
, H.
, and Imase
, K.
, 2009
, “Fundamental Analysis of a Cycloid Ball Reducer (5th Report)-Development of a two Stage Type Reduction Mechanism
,” JSPE
, 12
(75
), pp. 1418
–1422
. 10.2493/jjspe.75.14186.
Terada
, H.
, 2010
, “The Development of Gearless Reducers With Rolling Balls
,” J. Mech. Sci. Technol.
, 24
(1
), pp. 189
–195
. 10.1007/s12206-009-1155-07.
Bara
, M.
, Stan
, S. D.
, and Teutan
, E.
, 2009
, “Design and Virtual Reality Simulation of Frontal-Sinusoidal Ball Transmission
,” Mechanika
, 78
(4
), pp. 63
–68
.8.
Duan
, L.
, An
, Z.
, and Yang
, R.
, 2016
, “Mechanical Model of Coupling Rolling and Sliding Friction in Real-Time Non-clearance Precision Ball Transmission
,” Tribol. Int.
, 103
, pp. 218
–227
. 10.1016/j.triboint.2016.06.0329.
Yang
, R.
, and An
, Z.
, 2017
, “Theoretical Calculation and Experimental Verification of the Elastic Angle of a Cycloid Ball Planetary Transmission Based on the Axial Pretightening Force
,” Adv. Mech. Eng.
, 9
(10
), p. 1687814017734112
. 10.1177/168781401773411210.
Xu
, L.
, and Song
, W.
, 2018
, “Elastic Hydrodynamic Lubrication Analysis for a Sine Movable Tooth Drive
,” Adv. Mech. Eng.
, 10
(12
), p. 1687814018814101
. 10.1177/168781401881410111.
Sun
, P.
, An
, Z.
, and Jiang
, W.
, 2018
, “Analysis of non-Hertz Contact Stress and Bearing Capacity on Meshing Pairs in a Real-Time non-Clearance Precision Ball Transmission
,” J. Braz. Soc. Mech. Sci. Eng.
, 40
(6
), p. UNSP 304
. 10.1007/s40430-018-1197-212.
Moradikazerouni
, A.
, Afrand
, M.
, and Alsarraf
, J.
, 2019
, “Investigation of a Computer CPU Heat Sink Under Laminar Forced Convection Using a Structural Stability Method
,” Int. J. Heat Mass Transfer
, 134
, pp. 1218
–1226
. 10.1016/j.ijheatmasstransfer.2019.02.02913.
Moradikazerouni
, A.
, Afrand
, M.
, and Alsarraf
, J.
, 2019
, “Comparison of the Effect of Five Different Entrance Channel Shapes of a Micro-Channel Heat Sink in Forced Convection With Application to Cooling a Supercomputer Circuit Board
,” Appl. Therm. Eng.
, 150
, pp. 1078
–1089
. 10.1016/j.applthermaleng.2019.01.05114.
Wang
, L.
, Xu
, J.
, and Wang
, J.
, 2018
, “A Peridynamic Framework and Simulation of Non-Fourier and Nonlocal Heat Conduction
,” Int. J. Heat Mass Transfer
, 118
, pp. 1284
–1292
. 10.1016/j.ijheatmasstransfer.2017.11.07415.
Duda
, P.
, 2019
, “Simplification of 3D Transient Heat Conduction by Reducing It to an Axisymmetric Heat Conduction Problem and a New Inverse Method of the Problem Solution
,” Int. J. Heat Mass Transfer
, 143
, p. 118492
. 10.1016/j.ijheatmasstransfer.2019.11849216.
Kurata
, K.
, Yoshii
, T.
, and Uchida
, S.
, 2012
, “Visualization of Electroporation-Induced Temperature Rise Using Temperature-Sensitive Ink
,” Int. J. Heat Mass Transfer
, 55
(23–24
), pp. 7207
–7212
. 10.1016/j.ijheatmasstransfer.2012.07.03817.
Chen
, K.
, Wang
, S.
, and Song
, M.
, 2016
, “Temperature-Gradient-Aware Bionic Optimization Method for Heat Source Distribution in Heat Conduction
,” Int. J. Heat Mass Transfer
, 100
, pp. 737
–746
. 10.1016/j.ijheatmasstransfer.2016.05.01118.
Taburdagitan
, M.
, and Akkok
, M.
, 2006
, “Determination of Surface Temperature Rise With Thermo-Elastic Analysis of Spur Gears
,” Wear
, 261
(5–6
), pp. 656
–665
. 10.1016/j.wear.2006.01.01919.
Chen
, L.
, Wu
, X.
, and Qin
, D.
, 2011
, “An Experimental Study on the Transient Temperature Test of the Planetary Gear Reducer of the Epbm
,” J. Adv. Manuf. Syst.
, 10
(1
), pp. 37
–43
. 10.1142/S021968671100195320.
Wang
, Y.
, Niu
, W.
, and Chen
, Y.
, 2016
, “Convection Heat Transfer and Temperature Analysis of Oil Jet Lubricated Spur Gears
,” Iidustral Lubr. Tribol.
, 68
(6
), pp. 624
–631
. 10.1108/ILT-10-2015-014521.
Golbakhshi
, H.
, and Namjoo
, M.
, 2017
, “Thermo-Structural Analysis on Evaluating Effects of Friction and Transient Heat Transfer on Performance of Gears in High-Precision Assemblies
,” J. Cent. South Univ.
, 24
(1
), pp. 71
–80
. 10.1007/s11771-017-3410-322.
Evans
, S. M.
, and Keogh
, P. S.
, 2016
, “Efficiency and Running Temperature of a Polymer-Steel Spur Gear Pair From Slip/Roll Ratio Fundamentals
,” Tribol. Int.
, 97
, pp. 379
–389
. 10.1016/j.triboint.2016.01.05223.
Andersson
, M.
, Sosa
, M.
, and Olofsson
, U.
, 2017
, “Efficiency and Temperature of Spur Gears Using Spray Lubrication Compared to Dip Lubrication
,” Proc. Inst. Mech. Eng., Part J
, 231
(11
), pp. 1390
–1396
. 10.1177/135065011769570924.
Yang
, Y.
, Li
, W.
, and Wang
, J.
, 2019
, “On the Mixed EHL Characteristics, Friction and Flash Temperature in Helical Gears With Consideration of 3D Surface Roughness
,” Ind. Lubr. Tribol.
, 71
(1
), pp. 10
–21
. 10.1108/ILT-04-2017-011325.
Roda
, C. V.
, and Sanchez
, M. F.
, 2019
, “A 2D Finite Element Based Approach to Predict the Temperature Field in Polymer Spur Gear Transmissions
,” Mech. Mach. Theory
, 133
, pp. 195
–210
. 10.1016/j.mechmachtheory.2018.11.01926.
Pan
, W.
, Li
, X.
, and Wang
, L.
, 2019
, “Nonlinear Response Analysis of Gear-Shaft-Bearing System Considering Tooth Contact Temperature and Random Excitations
,” Appl. Math. Model.
, 68
, pp. 113
–136
. 10.1016/j.apm.2018.10.02227.
Ozisik
, M. N.
, 1980
, Heat Conditions
, John Wiley
, New York
.28.
Li
, L.
, Liang
, S.
, and Zhou
, J.
, 2015
, “Thermal Analysis of the Center Wheel for Swinging Movable Tooth Drive
,” J. Sichuan Univ. (Engineering Science Edition)
, 47
(4
), pp. 146
–150
.Copyright © 2020 by ASME
You do not currently have access to this content.
